-
Notifications
You must be signed in to change notification settings - Fork 2
/
nl80211.h
4040 lines (3709 loc) · 162 KB
/
nl80211.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
#ifndef __LINUX_NL80211_H
#define __LINUX_NL80211_H
/*
* 802.11 netlink interface public header
*
* Copyright 2006-2010 Johannes Berg <johannes@sipsolutions.net>
* Copyright 2008 Michael Wu <flamingice@sourmilk.net>
* Copyright 2008 Luis Carlos Cobo <luisca@cozybit.com>
* Copyright 2008 Michael Buesch <m@bues.ch>
* Copyright 2008, 2009 Luis R. Rodriguez <lrodriguez@atheros.com>
* Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
* Copyright 2008 Colin McCabe <colin@cozybit.com>
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*
*/
#include <linux/types.h>
#define NL80211_GENL_NAME "nl80211"
/**
* DOC: Station handling
*
* Stations are added per interface, but a special case exists with VLAN
* interfaces. When a station is bound to an AP interface, it may be moved
* into a VLAN identified by a VLAN interface index (%NL80211_ATTR_STA_VLAN).
* The station is still assumed to belong to the AP interface it was added
* to.
*
* Station handling varies per interface type and depending on the driver's
* capabilities.
*
* For drivers supporting TDLS with external setup (WIPHY_FLAG_SUPPORTS_TDLS
* and WIPHY_FLAG_TDLS_EXTERNAL_SETUP), the station lifetime is as follows:
* - a setup station entry is added, not yet authorized, without any rate
* or capability information, this just exists to avoid race conditions
* - when the TDLS setup is done, a single NL80211_CMD_SET_STATION is valid
* to add rate and capability information to the station and at the same
* time mark it authorized.
* - %NL80211_TDLS_ENABLE_LINK is then used
* - after this, the only valid operation is to remove it by tearing down
* the TDLS link (%NL80211_TDLS_DISABLE_LINK)
*
* TODO: need more info for other interface types
*/
/**
* DOC: Frame transmission/registration support
*
* Frame transmission and registration support exists to allow userspace
* management entities such as wpa_supplicant react to management frames
* that are not being handled by the kernel. This includes, for example,
* certain classes of action frames that cannot be handled in the kernel
* for various reasons.
*
* Frame registration is done on a per-interface basis and registrations
* cannot be removed other than by closing the socket. It is possible to
* specify a registration filter to register, for example, only for a
* certain type of action frame. In particular with action frames, those
* that userspace registers for will not be returned as unhandled by the
* driver, so that the registered application has to take responsibility
* for doing that.
*
* The type of frame that can be registered for is also dependent on the
* driver and interface type. The frame types are advertised in wiphy
* attributes so applications know what to expect.
*
* NOTE: When an interface changes type while registrations are active,
* these registrations are ignored until the interface type is
* changed again. This means that changing the interface type can
* lead to a situation that couldn't otherwise be produced, but
* any such registrations will be dormant in the sense that they
* will not be serviced, i.e. they will not receive any frames.
*
* Frame transmission allows userspace to send for example the required
* responses to action frames. It is subject to some sanity checking,
* but many frames can be transmitted. When a frame was transmitted, its
* status is indicated to the sending socket.
*
* For more technical details, see the corresponding command descriptions
* below.
*/
/**
* DOC: Virtual interface / concurrency capabilities
*
* Some devices are able to operate with virtual MACs, they can have
* more than one virtual interface. The capability handling for this
* is a bit complex though, as there may be a number of restrictions
* on the types of concurrency that are supported.
*
* To start with, each device supports the interface types listed in
* the %NL80211_ATTR_SUPPORTED_IFTYPES attribute, but by listing the
* types there no concurrency is implied.
*
* Once concurrency is desired, more attributes must be observed:
* To start with, since some interface types are purely managed in
* software, like the AP-VLAN type in mac80211 for example, there's
* an additional list of these, they can be added at any time and
* are only restricted by some semantic restrictions (e.g. AP-VLAN
* cannot be added without a corresponding AP interface). This list
* is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute.
*
* Further, the list of supported combinations is exported. This is
* in the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute. Basically,
* it exports a list of "groups", and at any point in time the
* interfaces that are currently active must fall into any one of
* the advertised groups. Within each group, there are restrictions
* on the number of interfaces of different types that are supported
* and also the number of different channels, along with potentially
* some other restrictions. See &enum nl80211_if_combination_attrs.
*
* All together, these attributes define the concurrency of virtual
* interfaces that a given device supports.
*/
/**
* DOC: packet coalesce support
*
* In most cases, host that receives IPv4 and IPv6 multicast/broadcast
* packets does not do anything with these packets. Therefore the
* reception of these unwanted packets causes unnecessary processing
* and power consumption.
*
* Packet coalesce feature helps to reduce number of received interrupts
* to host by buffering these packets in firmware/hardware for some
* predefined time. Received interrupt will be generated when one of the
* following events occur.
* a) Expiration of hardware timer whose expiration time is set to maximum
* coalescing delay of matching coalesce rule.
* b) Coalescing buffer in hardware reaches it's limit.
* c) Packet doesn't match any of the configured coalesce rules.
*
* User needs to configure following parameters for creating a coalesce
* rule.
* a) Maximum coalescing delay
* b) List of packet patterns which needs to be matched
* c) Condition for coalescence. pattern 'match' or 'no match'
* Multiple such rules can be created.
*/
/**
* enum nl80211_commands - supported nl80211 commands
*
* @NL80211_CMD_UNSPEC: unspecified command to catch errors
*
* @NL80211_CMD_GET_WIPHY: request information about a wiphy or dump request
* to get a list of all present wiphys.
* @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or
* %NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME,
* %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ (and the
* attributes determining the channel width; this is used for setting
* monitor mode channel), %NL80211_ATTR_WIPHY_RETRY_SHORT,
* %NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
* and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD.
* However, for setting the channel, see %NL80211_CMD_SET_CHANNEL
* instead, the support here is for backward compatibility only.
* @NL80211_CMD_NEW_WIPHY: Newly created wiphy, response to get request
* or rename notification. Has attributes %NL80211_ATTR_WIPHY and
* %NL80211_ATTR_WIPHY_NAME.
* @NL80211_CMD_DEL_WIPHY: Wiphy deleted. Has attributes
* %NL80211_ATTR_WIPHY and %NL80211_ATTR_WIPHY_NAME.
*
* @NL80211_CMD_GET_INTERFACE: Request an interface's configuration;
* either a dump request on a %NL80211_ATTR_WIPHY or a specific get
* on an %NL80211_ATTR_IFINDEX is supported.
* @NL80211_CMD_SET_INTERFACE: Set type of a virtual interface, requires
* %NL80211_ATTR_IFINDEX and %NL80211_ATTR_IFTYPE.
* @NL80211_CMD_NEW_INTERFACE: Newly created virtual interface or response
* to %NL80211_CMD_GET_INTERFACE. Has %NL80211_ATTR_IFINDEX,
* %NL80211_ATTR_WIPHY and %NL80211_ATTR_IFTYPE attributes. Can also
* be sent from userspace to request creation of a new virtual interface,
* then requires attributes %NL80211_ATTR_WIPHY, %NL80211_ATTR_IFTYPE and
* %NL80211_ATTR_IFNAME.
* @NL80211_CMD_DEL_INTERFACE: Virtual interface was deleted, has attributes
* %NL80211_ATTR_IFINDEX and %NL80211_ATTR_WIPHY. Can also be sent from
* userspace to request deletion of a virtual interface, then requires
* attribute %NL80211_ATTR_IFINDEX.
*
* @NL80211_CMD_GET_KEY: Get sequence counter information for a key specified
* by %NL80211_ATTR_KEY_IDX and/or %NL80211_ATTR_MAC.
* @NL80211_CMD_SET_KEY: Set key attributes %NL80211_ATTR_KEY_DEFAULT,
* %NL80211_ATTR_KEY_DEFAULT_MGMT, or %NL80211_ATTR_KEY_THRESHOLD.
* @NL80211_CMD_NEW_KEY: add a key with given %NL80211_ATTR_KEY_DATA,
* %NL80211_ATTR_KEY_IDX, %NL80211_ATTR_MAC, %NL80211_ATTR_KEY_CIPHER,
* and %NL80211_ATTR_KEY_SEQ attributes.
* @NL80211_CMD_DEL_KEY: delete a key identified by %NL80211_ATTR_KEY_IDX
* or %NL80211_ATTR_MAC.
*
* @NL80211_CMD_GET_BEACON: (not used)
* @NL80211_CMD_SET_BEACON: change the beacon on an access point interface
* using the %NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL
* attributes. For drivers that generate the beacon and probe responses
* internally, the following attributes must be provided: %NL80211_ATTR_IE,
* %NL80211_ATTR_IE_PROBE_RESP and %NL80211_ATTR_IE_ASSOC_RESP.
* @NL80211_CMD_START_AP: Start AP operation on an AP interface, parameters
* are like for %NL80211_CMD_SET_BEACON, and additionally parameters that
* do not change are used, these include %NL80211_ATTR_BEACON_INTERVAL,
* %NL80211_ATTR_DTIM_PERIOD, %NL80211_ATTR_SSID,
* %NL80211_ATTR_HIDDEN_SSID, %NL80211_ATTR_CIPHERS_PAIRWISE,
* %NL80211_ATTR_CIPHER_GROUP, %NL80211_ATTR_WPA_VERSIONS,
* %NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY,
* %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_INACTIVITY_TIMEOUT,
* %NL80211_ATTR_ACL_POLICY and %NL80211_ATTR_MAC_ADDRS.
* The channel to use can be set on the interface or be given using the
* %NL80211_ATTR_WIPHY_FREQ and the attributes determining channel width.
* @NL80211_CMD_NEW_BEACON: old alias for %NL80211_CMD_START_AP
* @NL80211_CMD_STOP_AP: Stop AP operation on the given interface
* @NL80211_CMD_DEL_BEACON: old alias for %NL80211_CMD_STOP_AP
*
* @NL80211_CMD_GET_STATION: Get station attributes for station identified by
* %NL80211_ATTR_MAC on the interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_SET_STATION: Set station attributes for station identified by
* %NL80211_ATTR_MAC on the interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_NEW_STATION: Add a station with given attributes to the
* the interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_DEL_STATION: Remove a station identified by %NL80211_ATTR_MAC
* or, if no MAC address given, all stations, on the interface identified
* by %NL80211_ATTR_IFINDEX.
*
* @NL80211_CMD_GET_MPATH: Get mesh path attributes for mesh path to
* destination %NL80211_ATTR_MAC on the interface identified by
* %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_SET_MPATH: Set mesh path attributes for mesh path to
* destination %NL80211_ATTR_MAC on the interface identified by
* %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_NEW_MPATH: Create a new mesh path for the destination given by
* %NL80211_ATTR_MAC via %NL80211_ATTR_MPATH_NEXT_HOP.
* @NL80211_CMD_DEL_MPATH: Delete a mesh path to the destination given by
* %NL80211_ATTR_MAC.
* @NL80211_CMD_NEW_PATH: Add a mesh path with given attributes to the
* the interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_DEL_PATH: Remove a mesh path identified by %NL80211_ATTR_MAC
* or, if no MAC address given, all mesh paths, on the interface identified
* by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_SET_BSS: Set BSS attributes for BSS identified by
* %NL80211_ATTR_IFINDEX.
*
* @NL80211_CMD_GET_REG: ask the wireless core to send us its currently set
* regulatory domain.
* @NL80211_CMD_SET_REG: Set current regulatory domain. CRDA sends this command
* after being queried by the kernel. CRDA replies by sending a regulatory
* domain structure which consists of %NL80211_ATTR_REG_ALPHA set to our
* current alpha2 if it found a match. It also provides
* NL80211_ATTR_REG_RULE_FLAGS, and a set of regulatory rules. Each
* regulatory rule is a nested set of attributes given by
* %NL80211_ATTR_REG_RULE_FREQ_[START|END] and
* %NL80211_ATTR_FREQ_RANGE_MAX_BW with an attached power rule given by
* %NL80211_ATTR_REG_RULE_POWER_MAX_ANT_GAIN and
* %NL80211_ATTR_REG_RULE_POWER_MAX_EIRP.
* @NL80211_CMD_REQ_SET_REG: ask the wireless core to set the regulatory domain
* to the specified ISO/IEC 3166-1 alpha2 country code. The core will
* store this as a valid request and then query userspace for it.
*
* @NL80211_CMD_GET_MESH_CONFIG: Get mesh networking properties for the
* interface identified by %NL80211_ATTR_IFINDEX
*
* @NL80211_CMD_SET_MESH_CONFIG: Set mesh networking properties for the
* interface identified by %NL80211_ATTR_IFINDEX
*
* @NL80211_CMD_SET_MGMT_EXTRA_IE: Set extra IEs for management frames. The
* interface is identified with %NL80211_ATTR_IFINDEX and the management
* frame subtype with %NL80211_ATTR_MGMT_SUBTYPE. The extra IE data to be
* added to the end of the specified management frame is specified with
* %NL80211_ATTR_IE. If the command succeeds, the requested data will be
* added to all specified management frames generated by
* kernel/firmware/driver.
* Note: This command has been removed and it is only reserved at this
* point to avoid re-using existing command number. The functionality this
* command was planned for has been provided with cleaner design with the
* option to specify additional IEs in NL80211_CMD_TRIGGER_SCAN,
* NL80211_CMD_AUTHENTICATE, NL80211_CMD_ASSOCIATE,
* NL80211_CMD_DEAUTHENTICATE, and NL80211_CMD_DISASSOCIATE.
*
* @NL80211_CMD_GET_SCAN: get scan results
* @NL80211_CMD_TRIGGER_SCAN: trigger a new scan with the given parameters
* %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the
* probe requests at CCK rate or not.
* @NL80211_CMD_NEW_SCAN_RESULTS: scan notification (as a reply to
* NL80211_CMD_GET_SCAN and on the "scan" multicast group)
* @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons,
* partial scan results may be available
*
* @NL80211_CMD_START_SCHED_SCAN: start a scheduled scan at certain
* intervals, as specified by %NL80211_ATTR_SCHED_SCAN_INTERVAL.
* Like with normal scans, if SSIDs (%NL80211_ATTR_SCAN_SSIDS)
* are passed, they are used in the probe requests. For
* broadcast, a broadcast SSID must be passed (ie. an empty
* string). If no SSID is passed, no probe requests are sent and
* a passive scan is performed. %NL80211_ATTR_SCAN_FREQUENCIES,
* if passed, define which channels should be scanned; if not
* passed, all channels allowed for the current regulatory domain
* are used. Extra IEs can also be passed from the userspace by
* using the %NL80211_ATTR_IE attribute.
* @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan. Returns -ENOENT
* if scheduled scan is not running.
* @NL80211_CMD_SCHED_SCAN_RESULTS: indicates that there are scheduled scan
* results available.
* @NL80211_CMD_SCHED_SCAN_STOPPED: indicates that the scheduled scan has
* stopped. The driver may issue this event at any time during a
* scheduled scan. One reason for stopping the scan is if the hardware
* does not support starting an association or a normal scan while running
* a scheduled scan. This event is also sent when the
* %NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface
* is brought down while a scheduled scan was running.
*
* @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation
* or noise level
* @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to
* NL80211_CMD_GET_SURVEY and on the "scan" multicast group)
*
* @NL80211_CMD_SET_PMKSA: Add a PMKSA cache entry, using %NL80211_ATTR_MAC
* (for the BSSID) and %NL80211_ATTR_PMKID.
* @NL80211_CMD_DEL_PMKSA: Delete a PMKSA cache entry, using %NL80211_ATTR_MAC
* (for the BSSID) and %NL80211_ATTR_PMKID.
* @NL80211_CMD_FLUSH_PMKSA: Flush all PMKSA cache entries.
*
* @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain
* has been changed and provides details of the request information
* that caused the change such as who initiated the regulatory request
* (%NL80211_ATTR_REG_INITIATOR), the wiphy_idx
* (%NL80211_ATTR_REG_ALPHA2) on which the request was made from if
* the initiator was %NL80211_REGDOM_SET_BY_COUNTRY_IE or
* %NL80211_REGDOM_SET_BY_DRIVER, the type of regulatory domain
* set (%NL80211_ATTR_REG_TYPE), if the type of regulatory domain is
* %NL80211_REG_TYPE_COUNTRY the alpha2 to which we have moved on
* to (%NL80211_ATTR_REG_ALPHA2).
* @NL80211_CMD_REG_BEACON_HINT: indicates to userspace that an AP beacon
* has been found while world roaming thus enabling active scan or
* any mode of operation that initiates TX (beacons) on a channel
* where we would not have been able to do either before. As an example
* if you are world roaming (regulatory domain set to world or if your
* driver is using a custom world roaming regulatory domain) and while
* doing a passive scan on the 5 GHz band you find an AP there (if not
* on a DFS channel) you will now be able to actively scan for that AP
* or use AP mode on your card on that same channel. Note that this will
* never be used for channels 1-11 on the 2 GHz band as they are always
* enabled world wide. This beacon hint is only sent if your device had
* either disabled active scanning or beaconing on a channel. We send to
* userspace the wiphy on which we removed a restriction from
* (%NL80211_ATTR_WIPHY) and the channel on which this occurred
* before (%NL80211_ATTR_FREQ_BEFORE) and after (%NL80211_ATTR_FREQ_AFTER)
* the beacon hint was processed.
*
* @NL80211_CMD_AUTHENTICATE: authentication request and notification.
* This command is used both as a command (request to authenticate) and
* as an event on the "mlme" multicast group indicating completion of the
* authentication process.
* When used as a command, %NL80211_ATTR_IFINDEX is used to identify the
* interface. %NL80211_ATTR_MAC is used to specify PeerSTAAddress (and
* BSSID in case of station mode). %NL80211_ATTR_SSID is used to specify
* the SSID (mainly for association, but is included in authentication
* request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ is used
* to specify the frequence of the channel in MHz. %NL80211_ATTR_AUTH_TYPE
* is used to specify the authentication type. %NL80211_ATTR_IE is used to
* define IEs (VendorSpecificInfo, but also including RSN IE and FT IEs)
* to be added to the frame.
* When used as an event, this reports reception of an Authentication
* frame in station and IBSS modes when the local MLME processed the
* frame, i.e., it was for the local STA and was received in correct
* state. This is similar to MLME-AUTHENTICATE.confirm primitive in the
* MLME SAP interface (kernel providing MLME, userspace SME). The
* included %NL80211_ATTR_FRAME attribute contains the management frame
* (including both the header and frame body, but not FCS). This event is
* also used to indicate if the authentication attempt timed out. In that
* case the %NL80211_ATTR_FRAME attribute is replaced with a
* %NL80211_ATTR_TIMED_OUT flag (and %NL80211_ATTR_MAC to indicate which
* pending authentication timed out).
* @NL80211_CMD_ASSOCIATE: association request and notification; like
* NL80211_CMD_AUTHENTICATE but for Association and Reassociation
* (similar to MLME-ASSOCIATE.request, MLME-REASSOCIATE.request,
* MLME-ASSOCIATE.confirm or MLME-REASSOCIATE.confirm primitives).
* @NL80211_CMD_DEAUTHENTICATE: deauthentication request and notification; like
* NL80211_CMD_AUTHENTICATE but for Deauthentication frames (similar to
* MLME-DEAUTHENTICATION.request and MLME-DEAUTHENTICATE.indication
* primitives).
* @NL80211_CMD_DISASSOCIATE: disassociation request and notification; like
* NL80211_CMD_AUTHENTICATE but for Disassociation frames (similar to
* MLME-DISASSOCIATE.request and MLME-DISASSOCIATE.indication primitives).
*
* @NL80211_CMD_MICHAEL_MIC_FAILURE: notification of a locally detected Michael
* MIC (part of TKIP) failure; sent on the "mlme" multicast group; the
* event includes %NL80211_ATTR_MAC to describe the source MAC address of
* the frame with invalid MIC, %NL80211_ATTR_KEY_TYPE to show the key
* type, %NL80211_ATTR_KEY_IDX to indicate the key identifier, and
* %NL80211_ATTR_KEY_SEQ to indicate the TSC value of the frame; this
* event matches with MLME-MICHAELMICFAILURE.indication() primitive
*
* @NL80211_CMD_JOIN_IBSS: Join a new IBSS -- given at least an SSID and a
* FREQ attribute (for the initial frequency if no peer can be found)
* and optionally a MAC (as BSSID) and FREQ_FIXED attribute if those
* should be fixed rather than automatically determined. Can only be
* executed on a network interface that is UP, and fixed BSSID/FREQ
* may be rejected. Another optional parameter is the beacon interval,
* given in the %NL80211_ATTR_BEACON_INTERVAL attribute, which if not
* given defaults to 100 TU (102.4ms).
* @NL80211_CMD_LEAVE_IBSS: Leave the IBSS -- no special arguments, the IBSS is
* determined by the network interface.
*
* @NL80211_CMD_TESTMODE: testmode command, takes a wiphy (or ifindex) attribute
* to identify the device, and the TESTDATA blob attribute to pass through
* to the driver.
*
* @NL80211_CMD_CONNECT: connection request and notification; this command
* requests to connect to a specified network but without separating
* auth and assoc steps. For this, you need to specify the SSID in a
* %NL80211_ATTR_SSID attribute, and can optionally specify the association
* IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_USE_MFP,
* %NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
* %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and
* %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT.
* Background scan period can optionally be
* specified in %NL80211_ATTR_BG_SCAN_PERIOD,
* if not specified default background scan configuration
* in driver is used and if period value is 0, bg scan will be disabled.
* This attribute is ignored if driver does not support roam scan.
* It is also sent as an event, with the BSSID and response IEs when the
* connection is established or failed to be established. This can be
* determined by the STATUS_CODE attribute.
* @NL80211_CMD_ROAM: request that the card roam (currently not implemented),
* sent as an event when the card/driver roamed by itself.
* @NL80211_CMD_DISCONNECT: drop a given connection; also used to notify
* userspace that a connection was dropped by the AP or due to other
* reasons, for this the %NL80211_ATTR_DISCONNECTED_BY_AP and
* %NL80211_ATTR_REASON_CODE attributes are used.
*
* @NL80211_CMD_SET_WIPHY_NETNS: Set a wiphy's netns. Note that all devices
* associated with this wiphy must be down and will follow.
*
* @NL80211_CMD_REMAIN_ON_CHANNEL: Request to remain awake on the specified
* channel for the specified amount of time. This can be used to do
* off-channel operations like transmit a Public Action frame and wait for
* a response while being associated to an AP on another channel.
* %NL80211_ATTR_IFINDEX is used to specify which interface (and thus
* radio) is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the
* frequency for the operation.
* %NL80211_ATTR_DURATION is used to specify the duration in milliseconds
* to remain on the channel. This command is also used as an event to
* notify when the requested duration starts (it may take a while for the
* driver to schedule this time due to other concurrent needs for the
* radio).
* When called, this operation returns a cookie (%NL80211_ATTR_COOKIE)
* that will be included with any events pertaining to this request;
* the cookie is also used to cancel the request.
* @NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL: This command can be used to cancel a
* pending remain-on-channel duration if the desired operation has been
* completed prior to expiration of the originally requested duration.
* %NL80211_ATTR_WIPHY or %NL80211_ATTR_IFINDEX is used to specify the
* radio. The %NL80211_ATTR_COOKIE attribute must be given as well to
* uniquely identify the request.
* This command is also used as an event to notify when a requested
* remain-on-channel duration has expired.
*
* @NL80211_CMD_SET_TX_BITRATE_MASK: Set the mask of rates to be used in TX
* rate selection. %NL80211_ATTR_IFINDEX is used to specify the interface
* and @NL80211_ATTR_TX_RATES the set of allowed rates.
*
* @NL80211_CMD_REGISTER_FRAME: Register for receiving certain mgmt frames
* (via @NL80211_CMD_FRAME) for processing in userspace. This command
* requires an interface index, a frame type attribute (optional for
* backward compatibility reasons, if not given assumes action frames)
* and a match attribute containing the first few bytes of the frame
* that should match, e.g. a single byte for only a category match or
* four bytes for vendor frames including the OUI. The registration
* cannot be dropped, but is removed automatically when the netlink
* socket is closed. Multiple registrations can be made.
* @NL80211_CMD_REGISTER_ACTION: Alias for @NL80211_CMD_REGISTER_FRAME for
* backward compatibility
* @NL80211_CMD_FRAME: Management frame TX request and RX notification. This
* command is used both as a request to transmit a management frame and
* as an event indicating reception of a frame that was not processed in
* kernel code, but is for us (i.e., which may need to be processed in a
* user space application). %NL80211_ATTR_FRAME is used to specify the
* frame contents (including header). %NL80211_ATTR_WIPHY_FREQ is used
* to indicate on which channel the frame is to be transmitted or was
* received. If this channel is not the current channel (remain-on-channel
* or the operational channel) the device will switch to the given channel
* and transmit the frame, optionally waiting for a response for the time
* specified using %NL80211_ATTR_DURATION. When called, this operation
* returns a cookie (%NL80211_ATTR_COOKIE) that will be included with the
* TX status event pertaining to the TX request.
* %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the
* management frames at CCK rate or not in 2GHz band.
* @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this
* command may be used with the corresponding cookie to cancel the wait
* time if it is known that it is no longer necessary.
* @NL80211_CMD_ACTION: Alias for @NL80211_CMD_FRAME for backward compatibility.
* @NL80211_CMD_FRAME_TX_STATUS: Report TX status of a management frame
* transmitted with %NL80211_CMD_FRAME. %NL80211_ATTR_COOKIE identifies
* the TX command and %NL80211_ATTR_FRAME includes the contents of the
* frame. %NL80211_ATTR_ACK flag is included if the recipient acknowledged
* the frame.
* @NL80211_CMD_ACTION_TX_STATUS: Alias for @NL80211_CMD_FRAME_TX_STATUS for
* backward compatibility.
*
* @NL80211_CMD_SET_POWER_SAVE: Set powersave, using %NL80211_ATTR_PS_STATE
* @NL80211_CMD_GET_POWER_SAVE: Get powersave status in %NL80211_ATTR_PS_STATE
*
* @NL80211_CMD_SET_CQM: Connection quality monitor configuration. This command
* is used to configure connection quality monitoring notification trigger
* levels.
* @NL80211_CMD_NOTIFY_CQM: Connection quality monitor notification. This
* command is used as an event to indicate the that a trigger level was
* reached.
* @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ
* and the attributes determining channel width) the given interface
* (identifed by %NL80211_ATTR_IFINDEX) shall operate on.
* In case multiple channels are supported by the device, the mechanism
* with which it switches channels is implementation-defined.
* When a monitor interface is given, it can only switch channel while
* no other interfaces are operating to avoid disturbing the operation
* of any other interfaces, and other interfaces will again take
* precedence when they are used.
*
* @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface.
*
* @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial
* mesh config parameters may be given.
* @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the
* network is determined by the network interface.
*
* @NL80211_CMD_UNPROT_DEAUTHENTICATE: Unprotected deauthentication frame
* notification. This event is used to indicate that an unprotected
* deauthentication frame was dropped when MFP is in use.
* @NL80211_CMD_UNPROT_DISASSOCIATE: Unprotected disassociation frame
* notification. This event is used to indicate that an unprotected
* disassociation frame was dropped when MFP is in use.
*
* @NL80211_CMD_NEW_PEER_CANDIDATE: Notification on the reception of a
* beacon or probe response from a compatible mesh peer. This is only
* sent while no station information (sta_info) exists for the new peer
* candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH,
* @NL80211_MESH_SETUP_USERSPACE_AMPE, or
* @NL80211_MESH_SETUP_USERSPACE_MPM is set. On reception of this
* notification, userspace may decide to create a new station
* (@NL80211_CMD_NEW_STATION). To stop this notification from
* reoccurring, the userspace authentication daemon may want to create the
* new station with the AUTHENTICATED flag unset and maybe change it later
* depending on the authentication result.
*
* @NL80211_CMD_GET_WOWLAN: get Wake-on-Wireless-LAN (WoWLAN) settings.
* @NL80211_CMD_SET_WOWLAN: set Wake-on-Wireless-LAN (WoWLAN) settings.
* Since wireless is more complex than wired ethernet, it supports
* various triggers. These triggers can be configured through this
* command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For
* more background information, see
* http://wireless.kernel.org/en/users/Documentation/WoWLAN.
* The @NL80211_CMD_SET_WOWLAN command can also be used as a notification
* from the driver reporting the wakeup reason. In this case, the
* @NL80211_ATTR_WOWLAN_TRIGGERS attribute will contain the reason
* for the wakeup, if it was caused by wireless. If it is not present
* in the wakeup notification, the wireless device didn't cause the
* wakeup but reports that it was woken up.
*
* @NL80211_CMD_SET_REKEY_OFFLOAD: This command is used give the driver
* the necessary information for supporting GTK rekey offload. This
* feature is typically used during WoWLAN. The configuration data
* is contained in %NL80211_ATTR_REKEY_DATA (which is nested and
* contains the data in sub-attributes). After rekeying happened,
* this command may also be sent by the driver as an MLME event to
* inform userspace of the new replay counter.
*
* @NL80211_CMD_PMKSA_CANDIDATE: This is used as an event to inform userspace
* of PMKSA caching dandidates.
*
* @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup).
* In addition, this can be used as an event to request userspace to take
* actions on TDLS links (set up a new link or tear down an existing one).
* In such events, %NL80211_ATTR_TDLS_OPERATION indicates the requested
* operation, %NL80211_ATTR_MAC contains the peer MAC address, and
* %NL80211_ATTR_REASON_CODE the reason code to be used (only with
* %NL80211_TDLS_TEARDOWN).
* @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame. The
* %NL80211_ATTR_TDLS_ACTION attribute determines the type of frame to be
* sent. Public Action codes (802.11-2012 8.1.5.1) will be sent as
* 802.11 management frames, while TDLS action codes (802.11-2012
* 8.5.13.1) will be encapsulated and sent as data frames. The currently
* supported Public Action code is %WLAN_PUB_ACTION_TDLS_DISCOVER_RES
* and the currently supported TDLS actions codes are given in
* &enum ieee80211_tdls_actioncode.
*
* @NL80211_CMD_UNEXPECTED_FRAME: Used by an application controlling an AP
* (or GO) interface (i.e. hostapd) to ask for unexpected frames to
* implement sending deauth to stations that send unexpected class 3
* frames. Also used as the event sent by the kernel when such a frame
* is received.
* For the event, the %NL80211_ATTR_MAC attribute carries the TA and
* other attributes like the interface index are present.
* If used as the command it must have an interface index and you can
* only unsubscribe from the event by closing the socket. Subscription
* is also for %NL80211_CMD_UNEXPECTED_4ADDR_FRAME events.
*
* @NL80211_CMD_UNEXPECTED_4ADDR_FRAME: Sent as an event indicating that the
* associated station identified by %NL80211_ATTR_MAC sent a 4addr frame
* and wasn't already in a 4-addr VLAN. The event will be sent similarly
* to the %NL80211_CMD_UNEXPECTED_FRAME event, to the same listener.
*
* @NL80211_CMD_PROBE_CLIENT: Probe an associated station on an AP interface
* by sending a null data frame to it and reporting when the frame is
* acknowleged. This is used to allow timing out inactive clients. Uses
* %NL80211_ATTR_IFINDEX and %NL80211_ATTR_MAC. The command returns a
* direct reply with an %NL80211_ATTR_COOKIE that is later used to match
* up the event with the request. The event includes the same data and
* has %NL80211_ATTR_ACK set if the frame was ACKed.
*
* @NL80211_CMD_REGISTER_BEACONS: Register this socket to receive beacons from
* other BSSes when any interfaces are in AP mode. This helps implement
* OLBC handling in hostapd. Beacons are reported in %NL80211_CMD_FRAME
* messages. Note that per PHY only one application may register.
*
* @NL80211_CMD_SET_NOACK_MAP: sets a bitmap for the individual TIDs whether
* No Acknowledgement Policy should be applied.
*
* @NL80211_CMD_CH_SWITCH_NOTIFY: An AP or GO may decide to switch channels
* independently of the userspace SME, send this event indicating
* %NL80211_ATTR_IFINDEX is now on %NL80211_ATTR_WIPHY_FREQ and the
* attributes determining channel width.
*
* @NL80211_CMD_START_P2P_DEVICE: Start the given P2P Device, identified by
* its %NL80211_ATTR_WDEV identifier. It must have been created with
* %NL80211_CMD_NEW_INTERFACE previously. After it has been started, the
* P2P Device can be used for P2P operations, e.g. remain-on-channel and
* public action frame TX.
* @NL80211_CMD_STOP_P2P_DEVICE: Stop the given P2P Device, identified by
* its %NL80211_ATTR_WDEV identifier.
*
* @NL80211_CMD_CONN_FAILED: connection request to an AP failed; used to
* notify userspace that AP has rejected the connection request from a
* station, due to particular reason. %NL80211_ATTR_CONN_FAILED_REASON
* is used for this.
*
* @NL80211_CMD_SET_MCAST_RATE: Change the rate used to send multicast frames
* for IBSS or MESH vif.
*
* @NL80211_CMD_SET_MAC_ACL: sets ACL for MAC address based access control.
* This is to be used with the drivers advertising the support of MAC
* address based access control. List of MAC addresses is passed in
* %NL80211_ATTR_MAC_ADDRS and ACL policy is passed in
* %NL80211_ATTR_ACL_POLICY. Driver will enable ACL with this list, if it
* is not already done. The new list will replace any existing list. Driver
* will clear its ACL when the list of MAC addresses passed is empty. This
* command is used in AP/P2P GO mode. Driver has to make sure to clear its
* ACL list during %NL80211_CMD_STOP_AP.
*
* @NL80211_CMD_RADAR_DETECT: Start a Channel availability check (CAC). Once
* a radar is detected or the channel availability scan (CAC) has finished
* or was aborted, or a radar was detected, usermode will be notified with
* this event. This command is also used to notify userspace about radars
* while operating on this channel.
* %NL80211_ATTR_RADAR_EVENT is used to inform about the type of the
* event.
*
* @NL80211_CMD_GET_PROTOCOL_FEATURES: Get global nl80211 protocol features,
* i.e. features for the nl80211 protocol rather than device features.
* Returns the features in the %NL80211_ATTR_PROTOCOL_FEATURES bitmap.
*
* @NL80211_CMD_UPDATE_FT_IES: Pass down the most up-to-date Fast Transition
* Information Element to the WLAN driver
*
* @NL80211_CMD_FT_EVENT: Send a Fast transition event from the WLAN driver
* to the supplicant. This will carry the target AP's MAC address along
* with the relevant Information Elements. This event is used to report
* received FT IEs (MDIE, FTIE, RSN IE, TIE, RICIE).
*
* @NL80211_CMD_CRIT_PROTOCOL_START: Indicates user-space will start running
* a critical protocol that needs more reliability in the connection to
* complete.
*
* @NL80211_CMD_CRIT_PROTOCOL_STOP: Indicates the connection reliability can
* return back to normal.
*
* @NL80211_CMD_GET_COALESCE: Get currently supported coalesce rules.
* @NL80211_CMD_SET_COALESCE: Configure coalesce rules or clear existing rules.
*
* @NL80211_CMD_CHANNEL_SWITCH: Perform a channel switch by announcing the
* the new channel information (Channel Switch Announcement - CSA)
* in the beacon for some time (as defined in the
* %NL80211_ATTR_CH_SWITCH_COUNT parameter) and then change to the
* new channel. Userspace provides the new channel information (using
* %NL80211_ATTR_WIPHY_FREQ and the attributes determining channel
* width). %NL80211_ATTR_CH_SWITCH_BLOCK_TX may be supplied to inform
* other station that transmission must be blocked until the channel
* switch is complete.
*
* @NL80211_CMD_VENDOR: Vendor-specified command/event. The command is specified
* by the %NL80211_ATTR_VENDOR_ID attribute and a sub-command in
* %NL80211_ATTR_VENDOR_SUBCMD. Parameter(s) can be transported in
* %NL80211_ATTR_VENDOR_DATA.
* For feature advertisement, the %NL80211_ATTR_VENDOR_DATA attribute is
* used in the wiphy data as a nested attribute containing descriptions
* (&struct nl80211_vendor_cmd_info) of the supported vendor commands.
* This may also be sent as an event with the same attributes.
*
* @NL80211_CMD_SET_QOS_MAP: Set Interworking QoS mapping for IP DSCP values.
* The QoS mapping information is included in %NL80211_ATTR_QOS_MAP. If
* that attribute is not included, QoS mapping is disabled. Since this
* QoS mapping is relevant for IP packets, it is only valid during an
* association. This is cleared on disassociation and AP restart.
*
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
*/
enum nl80211_commands {
/* don't change the order or add anything between, this is ABI! */
NL80211_CMD_UNSPEC,
NL80211_CMD_GET_WIPHY, /* can dump */
NL80211_CMD_SET_WIPHY,
NL80211_CMD_NEW_WIPHY,
NL80211_CMD_DEL_WIPHY,
NL80211_CMD_GET_INTERFACE, /* can dump */
NL80211_CMD_SET_INTERFACE,
NL80211_CMD_NEW_INTERFACE,
NL80211_CMD_DEL_INTERFACE,
NL80211_CMD_GET_KEY,
NL80211_CMD_SET_KEY,
NL80211_CMD_NEW_KEY,
NL80211_CMD_DEL_KEY,
NL80211_CMD_GET_BEACON,
NL80211_CMD_SET_BEACON,
NL80211_CMD_START_AP,
NL80211_CMD_NEW_BEACON = NL80211_CMD_START_AP,
NL80211_CMD_STOP_AP,
NL80211_CMD_DEL_BEACON = NL80211_CMD_STOP_AP,
NL80211_CMD_GET_STATION,
NL80211_CMD_SET_STATION,
NL80211_CMD_NEW_STATION,
NL80211_CMD_DEL_STATION,
NL80211_CMD_GET_MPATH,
NL80211_CMD_SET_MPATH,
NL80211_CMD_NEW_MPATH,
NL80211_CMD_DEL_MPATH,
NL80211_CMD_SET_BSS,
NL80211_CMD_SET_REG,
NL80211_CMD_REQ_SET_REG,
NL80211_CMD_GET_MESH_CONFIG,
NL80211_CMD_SET_MESH_CONFIG,
NL80211_CMD_SET_MGMT_EXTRA_IE /* reserved; not used */,
NL80211_CMD_GET_REG,
NL80211_CMD_GET_SCAN,
NL80211_CMD_TRIGGER_SCAN,
NL80211_CMD_NEW_SCAN_RESULTS,
NL80211_CMD_SCAN_ABORTED,
NL80211_CMD_REG_CHANGE,
NL80211_CMD_AUTHENTICATE,
NL80211_CMD_ASSOCIATE,
NL80211_CMD_DEAUTHENTICATE,
NL80211_CMD_DISASSOCIATE,
NL80211_CMD_MICHAEL_MIC_FAILURE,
NL80211_CMD_REG_BEACON_HINT,
NL80211_CMD_JOIN_IBSS,
NL80211_CMD_LEAVE_IBSS,
NL80211_CMD_TESTMODE,
NL80211_CMD_CONNECT,
NL80211_CMD_ROAM,
NL80211_CMD_DISCONNECT,
NL80211_CMD_SET_WIPHY_NETNS,
NL80211_CMD_GET_SURVEY,
NL80211_CMD_NEW_SURVEY_RESULTS,
NL80211_CMD_SET_PMKSA,
NL80211_CMD_DEL_PMKSA,
NL80211_CMD_FLUSH_PMKSA,
NL80211_CMD_REMAIN_ON_CHANNEL,
NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL,
NL80211_CMD_SET_TX_BITRATE_MASK,
NL80211_CMD_REGISTER_FRAME,
NL80211_CMD_REGISTER_ACTION = NL80211_CMD_REGISTER_FRAME,
NL80211_CMD_FRAME,
NL80211_CMD_ACTION = NL80211_CMD_FRAME,
NL80211_CMD_FRAME_TX_STATUS,
NL80211_CMD_ACTION_TX_STATUS = NL80211_CMD_FRAME_TX_STATUS,
NL80211_CMD_SET_POWER_SAVE,
NL80211_CMD_GET_POWER_SAVE,
NL80211_CMD_SET_CQM,
NL80211_CMD_NOTIFY_CQM,
NL80211_CMD_SET_CHANNEL,
NL80211_CMD_SET_WDS_PEER,
NL80211_CMD_FRAME_WAIT_CANCEL,
NL80211_CMD_JOIN_MESH,
NL80211_CMD_LEAVE_MESH,
NL80211_CMD_UNPROT_DEAUTHENTICATE,
NL80211_CMD_UNPROT_DISASSOCIATE,
NL80211_CMD_NEW_PEER_CANDIDATE,
NL80211_CMD_GET_WOWLAN,
NL80211_CMD_SET_WOWLAN,
NL80211_CMD_START_SCHED_SCAN,
NL80211_CMD_STOP_SCHED_SCAN,
NL80211_CMD_SCHED_SCAN_RESULTS,
NL80211_CMD_SCHED_SCAN_STOPPED,
NL80211_CMD_SET_REKEY_OFFLOAD,
NL80211_CMD_PMKSA_CANDIDATE,
NL80211_CMD_TDLS_OPER,
NL80211_CMD_TDLS_MGMT,
NL80211_CMD_UNEXPECTED_FRAME,
NL80211_CMD_PROBE_CLIENT,
NL80211_CMD_REGISTER_BEACONS,
NL80211_CMD_UNEXPECTED_4ADDR_FRAME,
NL80211_CMD_SET_NOACK_MAP,
NL80211_CMD_CH_SWITCH_NOTIFY,
NL80211_CMD_START_P2P_DEVICE,
NL80211_CMD_STOP_P2P_DEVICE,
NL80211_CMD_CONN_FAILED,
NL80211_CMD_SET_MCAST_RATE,
NL80211_CMD_SET_MAC_ACL,
NL80211_CMD_RADAR_DETECT,
NL80211_CMD_GET_PROTOCOL_FEATURES,
NL80211_CMD_UPDATE_FT_IES,
NL80211_CMD_FT_EVENT,
NL80211_CMD_CRIT_PROTOCOL_START,
NL80211_CMD_CRIT_PROTOCOL_STOP,
NL80211_CMD_GET_COALESCE,
NL80211_CMD_SET_COALESCE,
NL80211_CMD_CHANNEL_SWITCH,
NL80211_CMD_VENDOR,
NL80211_CMD_SET_QOS_MAP,
/* add new commands above here */
/* used to define NL80211_CMD_MAX below */
__NL80211_CMD_AFTER_LAST,
NL80211_CMD_MAX = __NL80211_CMD_AFTER_LAST - 1
};
/*
* Allow user space programs to use #ifdef on new commands by defining them
* here
*/
#define NL80211_CMD_SET_BSS NL80211_CMD_SET_BSS
#define NL80211_CMD_SET_MGMT_EXTRA_IE NL80211_CMD_SET_MGMT_EXTRA_IE
#define NL80211_CMD_REG_CHANGE NL80211_CMD_REG_CHANGE
#define NL80211_CMD_AUTHENTICATE NL80211_CMD_AUTHENTICATE
#define NL80211_CMD_ASSOCIATE NL80211_CMD_ASSOCIATE
#define NL80211_CMD_DEAUTHENTICATE NL80211_CMD_DEAUTHENTICATE
#define NL80211_CMD_DISASSOCIATE NL80211_CMD_DISASSOCIATE
#define NL80211_CMD_REG_BEACON_HINT NL80211_CMD_REG_BEACON_HINT
#define NL80211_ATTR_FEATURE_FLAGS NL80211_ATTR_FEATURE_FLAGS
/* source-level API compatibility */
#define NL80211_CMD_GET_MESH_PARAMS NL80211_CMD_GET_MESH_CONFIG
#define NL80211_CMD_SET_MESH_PARAMS NL80211_CMD_SET_MESH_CONFIG
#define NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE NL80211_MESH_SETUP_IE
/**
* enum nl80211_attrs - nl80211 netlink attributes
*
* @NL80211_ATTR_UNSPEC: unspecified attribute to catch errors
*
* @NL80211_ATTR_WIPHY: index of wiphy to operate on, cf.
* /sys/class/ieee80211/<phyname>/index
* @NL80211_ATTR_WIPHY_NAME: wiphy name (used for renaming)
* @NL80211_ATTR_WIPHY_TXQ_PARAMS: a nested array of TX queue parameters
* @NL80211_ATTR_WIPHY_FREQ: frequency of the selected channel in MHz,
* defines the channel together with the (deprecated)
* %NL80211_ATTR_WIPHY_CHANNEL_TYPE attribute or the attributes
* %NL80211_ATTR_CHANNEL_WIDTH and if needed %NL80211_ATTR_CENTER_FREQ1
* and %NL80211_ATTR_CENTER_FREQ2
* @NL80211_ATTR_CHANNEL_WIDTH: u32 attribute containing one of the values
* of &enum nl80211_chan_width, describing the channel width. See the
* documentation of the enum for more information.
* @NL80211_ATTR_CENTER_FREQ1: Center frequency of the first part of the
* channel, used for anything but 20 MHz bandwidth
* @NL80211_ATTR_CENTER_FREQ2: Center frequency of the second part of the
* channel, used only for 80+80 MHz bandwidth
* @NL80211_ATTR_WIPHY_CHANNEL_TYPE: included with NL80211_ATTR_WIPHY_FREQ
* if HT20 or HT40 are to be used (i.e., HT disabled if not included):
* NL80211_CHAN_NO_HT = HT not allowed (i.e., same as not including
* this attribute)
* NL80211_CHAN_HT20 = HT20 only
* NL80211_CHAN_HT40MINUS = secondary channel is below the primary channel
* NL80211_CHAN_HT40PLUS = secondary channel is above the primary channel
* This attribute is now deprecated.
* @NL80211_ATTR_WIPHY_RETRY_SHORT: TX retry limit for frames whose length is
* less than or equal to the RTS threshold; allowed range: 1..255;
* dot11ShortRetryLimit; u8
* @NL80211_ATTR_WIPHY_RETRY_LONG: TX retry limit for frames whose length is
* greater than the RTS threshold; allowed range: 1..255;
* dot11ShortLongLimit; u8
* @NL80211_ATTR_WIPHY_FRAG_THRESHOLD: fragmentation threshold, i.e., maximum
* length in octets for frames; allowed range: 256..8000, disable
* fragmentation with (u32)-1; dot11FragmentationThreshold; u32
* @NL80211_ATTR_WIPHY_RTS_THRESHOLD: RTS threshold (TX frames with length
* larger than or equal to this use RTS/CTS handshake); allowed range:
* 0..65536, disable with (u32)-1; dot11RTSThreshold; u32
* @NL80211_ATTR_WIPHY_COVERAGE_CLASS: Coverage Class as defined by IEEE 802.11
* section 7.3.2.9; dot11CoverageClass; u8
*
* @NL80211_ATTR_IFINDEX: network interface index of the device to operate on
* @NL80211_ATTR_IFNAME: network interface name
* @NL80211_ATTR_IFTYPE: type of virtual interface, see &enum nl80211_iftype
*
* @NL80211_ATTR_WDEV: wireless device identifier, used for pseudo-devices
* that don't have a netdev (u64)
*
* @NL80211_ATTR_MAC: MAC address (various uses)
*
* @NL80211_ATTR_KEY_DATA: (temporal) key data; for TKIP this consists of
* 16 bytes encryption key followed by 8 bytes each for TX and RX MIC
* keys
* @NL80211_ATTR_KEY_IDX: key ID (u8, 0-3)
* @NL80211_ATTR_KEY_CIPHER: key cipher suite (u32, as defined by IEEE 802.11
* section 7.3.2.25.1, e.g. 0x000FAC04)
* @NL80211_ATTR_KEY_SEQ: transmit key sequence number (IV/PN) for TKIP and
* CCMP keys, each six bytes in little endian
* @NL80211_ATTR_KEY_DEFAULT: Flag attribute indicating the key is default key
* @NL80211_ATTR_KEY_DEFAULT_MGMT: Flag attribute indicating the key is the
* default management key
* @NL80211_ATTR_CIPHER_SUITES_PAIRWISE: For crypto settings for connect or
* other commands, indicates which pairwise cipher suites are used
* @NL80211_ATTR_CIPHER_SUITE_GROUP: For crypto settings for connect or
* other commands, indicates which group cipher suite is used
*
* @NL80211_ATTR_BEACON_INTERVAL: beacon interval in TU
* @NL80211_ATTR_DTIM_PERIOD: DTIM period for beaconing
* @NL80211_ATTR_BEACON_HEAD: portion of the beacon before the TIM IE
* @NL80211_ATTR_BEACON_TAIL: portion of the beacon after the TIM IE
*
* @NL80211_ATTR_STA_AID: Association ID for the station (u16)
* @NL80211_ATTR_STA_FLAGS: flags, nested element with NLA_FLAG attributes of
* &enum nl80211_sta_flags (deprecated, use %NL80211_ATTR_STA_FLAGS2)
* @NL80211_ATTR_STA_LISTEN_INTERVAL: listen interval as defined by
* IEEE 802.11 7.3.1.6 (u16).
* @NL80211_ATTR_STA_SUPPORTED_RATES: supported rates, array of supported
* rates as defined by IEEE 802.11 7.3.2.2 but without the length
* restriction (at most %NL80211_MAX_SUPP_RATES).
* @NL80211_ATTR_STA_VLAN: interface index of VLAN interface to move station
* to, or the AP interface the station was originally added to to.
* @NL80211_ATTR_STA_INFO: information about a station, part of station info
* given for %NL80211_CMD_GET_STATION, nested attribute containing
* info as possible, see &enum nl80211_sta_info.
*
* @NL80211_ATTR_WIPHY_BANDS: Information about an operating bands,
* consisting of a nested array.
*
* @NL80211_ATTR_MESH_ID: mesh id (1-32 bytes).