Added the example guideline and template (#7665)

* Added the example guideline and template

* PR review changes with some typos and grammar fixes

* Changes according to the PR review

libraries/ESP32/examples/Template/ExampleTemplate/ExampleTemplate.ino

@@ -0,0 +1,16 @@
+/* Arduino Example Template
+
+   This example code is in the Public Domain (or CC0 licensed, at your option.)
+
+   Unless required by applicable law or agreed to in writing, this
+   software is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
+   CONDITIONS OF ANY KIND, either express or implied.
+*/
+
+void setup() {
+
+}
+
+void loop() {
+
+}

libraries/ESP32/examples/Template/ExampleTemplate/README.md

@@ -0,0 +1,122 @@
+# Arduino-ESP32 Example/Library Name ==(REQUIRED)==
+
+==*Add a brief description of this example/library here!*==
+
+This example/library demonstrates how to create a new example README file.
+
+# Supported Targets ==(REQUIRED)==
+
+==*Add the supported devices here!*==
+
+Currently, this example supports the following targets.
+
+| Supported Targets | ESP32 | ESP32-S2 | ESP32-C3 |
+| ----------------- | ----- | -------- | -------- |
+
+## How to Use Example/Library ==(OPTIONAL)==
+
+==*Add a brief description of how to use this example.*==
+
+* How to install the Arduino IDE: [Install Arduino IDE](https://github.com/espressif/arduino-esp32/tree/master/docs/arduino-ide).
+
+### Hardware Connection ==(OPTIONAL)==
+
+==*Add a brief description of wiring or any other hardware-specific connection.*==
+
+To use this example, you need to connect the LED to the `GPIOx`.
+
+SDCard GPIO connection scheme:
+
+| SDCard Pin  | Function | GPIO   |
+| ----------- | -------- | ------ |
+| 1           | CS       | GPIO5  |
+| 2           | DI/MOSI  | GPIO23 |
+| 3           | VSS/GND  | GND    |
+| 4           | VDD/3V3  | 3V3    |
+| 5           | SCLK     | GPIO18 |
+| 6           | VSS/GND  | GND    |
+| 7           | DO/MISO  | GPIO19 |
+
+To add images, please create a folder `_asset` inside the example folder to add the relevant images.
+
+### Configure the Project ==(OPTIONAL)==
+
+==*Add a brief description of this example here!*==
+
+Set the LED GPIO by changing the `LED_BUILTIN` value in the function `pinMode(LED_BUILTIN, OUTPUT);`. By default, the GPIO is: `GPIOx`.
+
+#### Example for the GPIO4:
+
+==*Add some code explanation if relevant to the example.*==
+
+```cpp
+// the setup function runs once when you press reset or power the board
+void setup() {
+// initialize digital pin 4 as an output.
+pinMode(4, OUTPUT);
+}
+```
+
+#### Using Arduino IDE
+
+To get more information about the Espressif boards see [Espressif Development Kits](https://www.espressif.com/en/products/devkits).
+
+* Before Compile/Verify, select the correct board: `Tools -> Board`.
+* Select the COM port: `Tools -> Port: xxx` where the `xxx` is the detected COM port.
+
+#### Using Platform IO
+
+* Select the COM port: `Devices` or set the `upload_port` option on the `platformio.ini` file.
+
+## Example/Log Output ==(OPTIONAL)==
+
+==*Add the log/serial output here!*==
+
+```
+ets Jul 29 2019 12:21:46
+
+rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
+configsip: 0, SPIWP:0xee
+clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
+mode:DIO, clock div:1
+load:0x3fff0030,len:1412
+load:0x40078000,len:13400
+load:0x40080400,len:3672
+entry 0x400805f8
+ESP32 Chip model = ESP32-D0WDQ5 Rev 3
+This chip has 2 cores
+Chip ID: 3957392
+```
+
+## Troubleshooting ==(REQUIRED)==
+
+==*Add specific issues you may find by using this example here!*==
+
+***Important: Make sure you are using a good quality USB cable and that you have a reliable power source***
+
+* **LED not blinking:** Check the wiring connection and the IO selection.
+* **Programming Fail:** If the programming/flash procedure fails, try reducing the serial connection speed.
+* **COM port not detected:** Check the USB cable and the USB to Serial driver installation.
+
+If the error persists, you can ask for help at the official [ESP32 forum](https://esp32.com) or see [Contribute](#contribute).
+
+## Contribute ==(REQUIRED)==
+
+==*Do not change! Keep it as is.*==
+
+To know how to contribute to this project, see [How to contribute.](https://github.com/espressif/arduino-esp32/blob/master/CONTRIBUTING.rst)
+
+If you have any **feedback** or **issue** to report on this example/library, please open an issue or fix it by creating a new PR. Contributions are more than welcome!
+
+Before creating a new issue, be sure to try Troubleshooting and check if the same issue was already created by someone else.
+
+## Resources ==(REQUIRED)==
+
+==*Do not change here! Keep it as is or add only relevant documents/info for this example. Do not add any purchase link/marketing stuff*==
+
+* Official ESP32 Forum: [Link](https://esp32.com)
+* Arduino-ESP32 Official Repository: [espressif/arduino-esp32](https://github.com/espressif/arduino-esp32)
+* ESP32 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32_datasheet_en.pdf)
+* ESP32-S2 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-s2_datasheet_en.pdf)
+* ESP32-C3 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-c3_datasheet_en.pdf)
+* Official ESP-IDF documentation: [ESP-IDF](https://idf.espressif.com)