Skip to content

rprinz08/UP42

Repository files navigation

UP42 - A Walkera UP02 Quadcopter firmware flasher clone

UP42 is a multi platform (Windows 32/64, Linux 32/64) command line utility with the following features:

  • Walkera firmware en-/decryption
  • Serial port DTR can be used to force receiver into boot loader mode
  • Configurable profiles in simple '.ini' file style config file
  • fast

Command line usage

The UP42 flasher understands these command line arguments:

-h, --help

Show help/usage informations.

-V, --version

Displays version information.

-v, --verbose

Enables verbose mode. If used multiple times (e.g. -v -v -v or -vvv) different debug informations will be shown.

-c, --config

Specifies which config file to use. Defaults to binary.ini. If binary is named up42, up42.ini is used as default config file name.

-I, --info

Connects to a Walkera receiver board and displays it's information string. Does not flash firmware.

-P, --profile

Defines which profile should be used from the config file.

-q, --quiet

Be quiet. Dont output any messages except data.

-s, --simple

Use simple console output (e.g. when running inside an IDE).

-i, --input

Input file to send. If '-' stdin will be used.

-x, --intelhex

Input file is not a binary but in INTEL hex.

-o, --output

Output file after encryption with key. If '-' stdout will be used. If no key specified outputFile == inputFile. If no output file is specified and a key is present a temporary output file is created which is deleted after flashing.

-k, --key

Key to XOR-encrypt inputFile with. Can be either:

  • a hex string starting with '0x'
  • the name of a file which content is used as key
  • if not hex or file the character string itself

If omitted no encryption is performed on input file.

-p, --port

Name of the serial port to send the encrypted output file via XModem to. If omitted nothing will be sent.

-b, --baud

Baude rate to use. Defaults to 9600.

-1, -2

1 or 2 stop bits.

-7, -8

7 or 8 data bits.

-N, -E, -O

No, Even or Odd parity.

-D, --nodtr

Disable DTR control.

-d, --invdtr

Inverse DTR handling.

Configuration

A UP42 config file is a simple '.ini' file where each section represents a so called profile.

This is a sample file for two Walkera receiver models. A Hoten-X RX2635H and a QR-Ladybird RX2634H:

[RX2635H]
name=RX2635H
description=Walkera Hoten-X
key=0x8E500166526E7BD7EEC85C7AC05AD792
input=MyFirmware.bin
output=MyFirmware.fw
port=COM1
; Walkera normally uses 38400,N,8,1 baud
baud=38400
; 7 or 8 data bits
dataBits=8
; 0=one stopbit, 1=one and a half stop bit, 2=two stopbits
stopBits=0
; 0=no, 1=odd, 2=even, 3=mark, 4=space
parity=0


[RX2634H]
name=RX2634H
description=Walkera QR-LadyBird
key=0xD0943F8C297615D82040E32745D848AD

In this sample the profile RX2635H defines values for the command line parameters (in order) -k, -i, -o, -p, -b, -8, -N. So you can simply call up42 -P RX2635H to:

  • encrypt the file MyFirmware.bin with the key 0x8E500166526E7BD7EEC85C7AC05AD792
  • write the encrypted content to file MyFirmware.fw
  • flash the receiver using XMODEM via port COM1, 38400 baud, no parity, 8 databits and 1 stopbit

After flashing the receiver the bootloader mode is ended and the new firmware is started.

Compiling

Windows

Building on Windows can be done in two ways:

  1. building with TCC (Tiny C compiler) If you dont have Visual Studio available or dont want install it wasting some gigabytes of disk space, UP42 can be compiled using TCC from http://bellard.org/tcc/. Download and install the 32 or 64 bit version and change the build.cmd file with the path to TCC. You will also need GNU make for Windows from http://gnuwin32.sourceforge.net/packages/make.htm

  2. building using Microsoft Visual Studio. For building UP42 with Visual Studio there is a solution file (.sln) included. Open it with Visual Studio and compile it either for 32 or 64 bit.

Prebuilt Windows binaries for the current version 1.5 are available:

  1. Version 1.5 for Windows 32 bit
  2. Version 1.5 for Windows 64 bit

Linux

To build under Linux you can use the included build.sh shell script which uses make and gcc.

Included is a .vscode folder with Visual Studio Code (VSCODE) settings allowing compiling UP42 with TCC from inside VSCODE by pressing CTRL+SHIFT+P and run task ....

Connecting the board / the flash cable

UP42 needs a serial connection to the receiver board. Walkera receivers work with low voltage (3.3V) wheras a PC serial port uses 12 Volts. So directly connecting the receiver to the PC is not a good idea. A level shifter like the MAX3232 from Maxim must be used.

Such a cable was already shown in another post. UP42 can be used with this cable but you have to manually enter bootloader mode by reseting (powering on) the receiver while UP42 waits for the board to become ready (about ~ 10 seconds).

This can be automated by using the serial port DTR line to reset the board during the wait time. Thus making firmware updates completely automatic. For this to work the following modified cable must be used.

Board reset can be performed in two ways:

  1. by connecting the DTR reset to PDI_CLK
  2. or by using a FET transistor to toggle power and thus reseting the board

Only use one method. If you use method #1 leave out T1 and make a straight GND connection. When using method #2 just leave PDI_CLK unconnected.

Usage

UP42 can be used to:

  • flash firmware to the receiver
  • identify a receiver
  • XOR encrypt or decrypt receiver firmware

If at least an input file, a key and a port is specified UP42 tries first to encrypt the input file with the given key and then flashes the encrypted firmware to the board. If no key is specified then the input file is flashed without encryption. This is usefull when flashing original Walkera firmware files which are already encrypted. If an input, and output file and a key is given but no port only an encryption is done. As XOR encryption is symetric this can also be used to decrypt (e.g. original Walkera firmware) files by using the encrypted file as input. When the -I (--info) parameter is used no encryption or flashing is done. Instead UP42 tries to connect to the board and will display it's ID string on the console.

About

A Walkera UP02 firmware flasher clone

Resources

Stars

Watchers

Forks

Packages

No packages published

Languages