Skip to content

Commit

Permalink
ARM: dts: sun7i: Add dts file for Bananapro board
Browse files Browse the repository at this point in the history
Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
  • Loading branch information
jwrdegoede authored and mripard committed Jan 21, 2015
1 parent 121b96c commit 10662a3
Show file tree
Hide file tree
Showing 2 changed files with 263 additions and 0 deletions.
1 change: 1 addition & 0 deletions arch/arm/boot/dts/Makefile
Original file line number Diff line number Diff line change
Expand Up @@ -465,6 +465,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \
sun6i-a31s-cs908.dtb
dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-bananapi.dtb \
sun7i-a20-bananapro.dtb \
sun7i-a20-cubieboard2.dtb \
sun7i-a20-cubietruck.dtb \
sun7i-a20-hummingbird.dtb \
Expand Down
262 changes: 262 additions & 0 deletions arch/arm/boot/dts/sun7i-a20-bananapro.dts
Original file line number Diff line number Diff line change
@@ -0,0 +1,262 @@
/*
* Copyright 2015 Hans de Goede <hdegoede@redhat.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public
* License along with this file; if not, write to the Free
* Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
* MA 02110-1301 USA
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/

/dts-v1/;
#include "sun7i-a20.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>

/ {
model = "LeMaker Banana Pro";
compatible = "lemaker,bananapro", "allwinner,sun7i-a20";

leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins_bananapro>;

blue {
label = "bananapro:blue:usr";
gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>;
};

green {
label = "bananapro:green:usr";
gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
};
};

reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&gmac_power_pin_bananapro>;
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
startup-delay-us = <100000>;
enable-active-high;
gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
};

reg_vmmc3: vmmc3 {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&vmmc3_pin_bananapro>;
regulator-name = "vmmc3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
enable-active-high;
gpio = <&pio 7 22 GPIO_ACTIVE_HIGH>;
};
};

&ahci {
status = "okay";
};

&ehci0 {
status = "okay";
};

&ehci1 {
status = "okay";
};

&gmac {
pinctrl-names = "default";
pinctrl-0 = <&gmac_pins_rgmii_a>;
phy = <&phy1>;
phy-mode = "rgmii";
phy-supply = <&reg_gmac_3v3>;
status = "okay";

phy1: ethernet-phy@1 {
reg = <1>;
};
};

&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";

axp209: pmic@34 {
compatible = "x-powers,axp209";
reg = <0x34>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;

interrupt-controller;
#interrupt-cells = <1>;
};
};

&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};

&ir0 {
pinctrl-names = "default";
pinctrl-0 = <&ir0_pins_a>;
status = "okay";
};

&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapro>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
cd-inverted;
status = "okay";
};

&mmc3 {
pinctrl-names = "default";
pinctrl-0 = <&mmc3_pins_a>;
vmmc-supply = <&reg_vmmc3>;
bus-width = <4>;
non-removable;
status = "okay";
};

&ohci0 {
status = "okay";
};

&ohci1 {
status = "okay";
};

&pio {
gmac_power_pin_bananapro: gmac_power_pin@0 {
allwinner,pins = "PH23";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};

led_pins_bananapro: led_pins@0 {
allwinner,pins = "PH24", "PG2";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};

mmc0_cd_pin_bananapro: mmc0_cd_pin@0 {
allwinner,pins = "PH10";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};

usb1_vbus_pin_bananapro: usb1_vbus_pin@0 {
allwinner,pins = "PH0";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};

usb2_vbus_pin_bananapro: usb2_vbus_pin@0 {
allwinner,pins = "PH1";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};

vmmc3_pin_bananapro: vmmc3_pin@0 {
allwinner,pins = "PH22";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};

&reg_usb1_vbus {
pinctrl-0 = <&usb1_vbus_pin_bananapro>;
gpio = <&pio 7 0 GPIO_ACTIVE_HIGH>; /* PH0 */
status = "okay";
};

&reg_usb2_vbus {
pinctrl-0 = <&usb2_vbus_pin_bananapro>;
gpio = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
status = "okay";
};

&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi0_pins_a>;
status = "okay";
};

&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};

&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins_a>;
status = "okay";
};

&uart7 {
pinctrl-names = "default";
pinctrl-0 = <&uart7_pins_a>;
status = "okay";
};

&usbphy {
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb2_vbus>;
status = "okay";
};

0 comments on commit 10662a3

Please sign in to comment.